Name: GR1 Titanium Plate Customized Suppliers, Manufacturers - Free Sample - TOPTITECH Metal Materials
Brand: TOPTITECH
SKU: 189114375

What is the titanium plate?

Titanium Grade 1 is an unalloyed, low-strength titanium product containing low oxygen with high form-ability; this titanium grade is used in airframes, heat exchangers, and desalination units.

Titanium Grade 2 is an unalloyed, medium-strength titanium product. This titanium grade is used in airframes, aircraft engines, and marine parts; good weld-ability and corrosion resistance are its distinguishing characteristics.

Titanium Grade 3 is an unalloyed, high strength, titanium product providing excellent corrosion resistance and good weld-ability. This titanium grade is primarily used in air-frame and aircraft engine parts.

Titanium Grade 4 is the highest strength pure unalloyed titanium product. This titanium grade is used almost exclusively for air-frame, aircraft engine parts, marine, surgical implants, and hydraulic tubing. Good formability and corrosion resistance are its hallmarks.

Production Introduction

American label numbers: GR1, GR2, GR5,

Chinese brand: TA1, TA2, TA10, TB2, TC4

Standard:

Certificate: ISO9001:2015

Original Country: China

Surface: Smooth and Shining

Payment term: TT

Port: Shanghai or Tianjin

The Surface Quality of Titanium Plates

1. The plate's surface should be smooth, clean, and metallic. The plate is allowed to be supplied with the sandblasted surface;

2. Slight darkening and local watermarks are allowed on the surface of the plate; Local scratches, indentation, pits, and other defects not exceeding half of the thickness tolerance are allowed, but the minimum thickness should be guaranteed;

3. The surface of the plate is not allowed to have cracks, skinning, oxide skinning, folding, metal, and non-metal inclusions, and other macroscopic defects and traces of alkali washing;

4, the plate is allowed to roll direction clear local defects, but the thickness of the plate after removal shall not be less than the minimum allowable thickness;

5. If there are special requirements on the surface quality of the plate, the supply can be negotiated by the supply and demand parties.

Titanium Plate Process

Hot forging: Forging process above the recrystallization temperature of the metal.

Hot rolling: Rolling process at a temperature higher than recrystallization.

Cold rolling: a rolling process in which the plastic deformation temperature is lower than the recovery temperature.

Annealing: A metal heat treatment process in which the metal is slowly heated to a certain temperature, held for sufficient time, and then cooled (usually slowly, sometimes controlled) at a suitable rate.

Pickling: immersing pieces in an aqueous solution such as sulfuric acid to remove thin films such as oxides on the surface of the metal. It is the pre-treatment or intermediate treatment of electroplating, enamel, rolling, and other processes.

Advantages of titanium plate

1. Titanium plate is the surface of the oxidized film equivalent to a good wear-resistant hair separation agent, the use of a titanium plate saves the separation agent so that the plate is easy to peel, and avoids the process of plate pre-treatment, titanium plate is half lighter than the copper plate.

2. The service life of a titanium plate is more than 3 times that of a copper plate, up to 10 to 20 years according to operating conditions.

3. The electrolytic copper made of titanium plate has a dense crystalline structure, smooth surface, and excellent quality.

4. Because the titanium plate does not need to be coated with a separation agent, it can avoid the pollution of copper electrolytes.

5. Improve the production capacity and reduce the production cost of electrolytic copper, so as to have better economic benefits.

How to inspect the titanium plate in TOPTITECH?

The hot rolled surface of the titanium plate should be smooth and clean. The sheet allows acid and alkali washing, sandblasting, and sanding surface supply.
Slight darkening and local watermarks are allowed on the surface of the titanium plate; There may be local scratches, indentation, pits, and other defects that do not exceed the allowable deviation of their thickness.
The surface of the titanium plate is not allowed to have cracks, skinning, oxidation skinning, folding, metal, non-metal clips, or alkali washing traces.
The titanium plate is allowed to remove local defects along the rolling direction, but the thickness of the container after removal shall not be less than the smaller allowable thickness.
The titanium plates should not be delaminated.
If there are special requirements on appearance quality, they can be negotiated by the supply and demand parties.